Toggle Nav
Menu
Account
Search
Advanced Search

Seablazex3 Guide

SEABLAZE X3 INSTALLATION GUIDE

STEP 1 - GET STARTED

What is in the box?

1 - SBX3 Light with 5 ft of 16 AWG Wire 

3 - 316 Stainless Screws (#8 1.5")

1 - Instruction Sheet
 

If you are missing or have misplaced a part, please contact our support team to assist. DO NOT return the product to the store.

What do I need?

  • Marine grade sealant (3M 4200 or equivalent)
  • Power driver/drill
  • Waterproof Butt Splice connectors
  • Heat Gun for shrinking waterproof butt splice connectors
  • Fuse per light (7.5A @12vDC or 5A @24vDC)
  • Wire strippers
  • Crimp Tool for butt splice connectors
  • Additional Wire (see chart here)
  • Multimeter for testing (optional)
  • 1.5A SPST switch (not included) for 3-Wire to switch
  • 7.5A Min SPST switch (not included) for 2-Wire to switch for 1 12vDC light (15A for 2 lights @12vDC)
  • Lumitec Poco Digital Lighting Control (optional)

STEP 2 - IMPORTANT INFORMATION

Transom Mount Lights

Underwater light placement can be subjective and vary depending on the style of the boat and the owner's personal preferences. This section will provide some guidance on best practices and our recommendations. 

  • It is best to place a light 6"-12" (150 mm-300 mm) below the waterline.
  • Place lights at intervals of 1 ft (0.3m) to 3 ft (0.9m).
  • For outboard motors, place lights between motors (see diagram).
  • The mounting hole size is 0.5"
  • Do not use power tools to tighten the "bronze" screws
  • Light placement on running surfaces is not recommended

Lumitec Limited Warranty:
Lumitec, LLC (“Lumitec”) warrants, to the original purchaser only, that the Lumitec product will be free from defects in manufacturing, workmanship, and materials for a period of five (5) years from the date of original purchase. This Limited Warranty is not transferable for any reason, including in the event the applicable product is sold, traded, transferred or otherwise
disposed of in any manner by the original purchaser to another party.


Proper installation and operation of this lighting product must comply with all applicable marine electrical standards, including those published by the American Boat and Yacht Council (ABYC). All wiring supplying power to this product must be protected in accordance with ABYC recommendations for 16 AWG, 105°C–rated conductors, including but not limited to proper over-current protection, circuit breaker or fuse sizing, conductor routing, chafe protection, and environmental shielding.


Failure to follow ABYC-compliant practices may result in equipment damage, reduced performance, or increased risk of fire, electric shock, or personal injury. The installer and vessel owner are solely responsible for ensuring that all electrical components and installation methods meet ABYC standards and any other applicable regulations. Lumitec assumes no liability for damages or in

STEP 3 - CONFIGURATION

Select the installation configuration you will be using for your light.

The Simplest Installation.

Great for Multi-light Installations.

Provides the Most Control Over Your Lighting.

TROUBLESHOOTING

Problem Cause Solution
Problem: Light Does not power on (2-Wire to Switch). Cause: Red and Orange wire are not receiving + voltage. Ground wire disconnected. Solution: Check power. Check fuse is not blown. Check ground wire connection. Check the switch and ensure it is rated for the load. Check voltage polarity.
Problem: Light Does not power on (3-Wire to Switch). Cause: Red and/or Orange wires are not receiving positive (+) voltage. Ground wire disconnected. Solution: Check power. Check fuse is not blown. Check ground wire connection. Check switch is in the ON position.
Problem: Light Does not power on (3-Wire to Poco). Cause: Red wire not receiving positive (+) voltage. Orange wire not connected to Poco Channel output. Poco is not setup correctly. Solution: Check power. Check fuse is not blown. Check ground wire connection. Check Poco Configuration (light group set to Clan 4). If Clan 4 does not exist in Light Groups, update your Poco firmware. Check Poco Configuration to ensure Switch is set to the correct Light Group.
Problem: Light Quickly Blinks. Cause: Insufficient voltage or current at light. Solution: Check for proper voltage at light (10vDC minimum required). Ensure the battery is at full charge. Verify wire gauge size is sufficient for no more than a 3% voltage drop.